Dutchwest Federal Airtight Manual
My method of operating a Consolidated Dutchwest Federal Airtight woodburning stove. Please be sure to watch the rest of this video in Parts 2 & 3. I decided to try using the side door. Replacement parts for the Vermont Castings Dutchwest wood & coal stove models. There were many different versions of the Dutchwest stoves made over the years. Please check your owners manual for part. Add to Cart Compare Quick view. Add to Cart Compare. Vermont Castings. Vermont Castings Ceramic Handle - Complete. 
• For safety, follow all installation, operation and maintenance directions. Contact local building officials about restrictions and installation inspection requirements in your area. DO NOT DISCARD THIS MANUAL: Retain for future use Convection Heater Model 2460, 2461, 2462 SAFETY NOTICE 7001135 1/07 Rev. • Dutchwest The Dutchwest models covered in this Owner’s Guide have been tested and listed by Inchcape Testing Services / Warnock Hersey of Middleton, Wiscon- sin.
The test standards utilized were ANSI/UL 1482 for the United States and CAN/CGA - B366.2 for Canada. Dutchwest models are not listed for mobile home installations. Under specific conditions used during EPA emissions testing.
Based on preliminary results obtained during EPA emissions testing. 7001135 Specifications 2460 22” (560 mm) 25³⁄₄” (654 mm) 21” (530 mm) 24¹⁄₂” (620 mm) 1135 29³⁄₄”.
• Dutchwest SAFETY NOTICE: IF YOUR DUTCHWEST CON- VECTION HEATER IS NOT PROPERLY INSTALLED, OPERATED AND MAINTAINED, A HOUSE FIRE MAY RESULT. FOR SAFETY, FOLLOW ALL INSTALLA- TION, OPERATION AND MAINTENANCE DIREC- TIONS. CONTACT LOCAL BUILDING OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA. Gps utility 515 crack. • The single-wall chimney connector should be made of 24 gauge or heavier steel, and must have a minimum internal diameter of 6” (150 mm) for models 2460 and 2461, or 8” (200 mm) for model 2462. Install single-wall chimney connector not less than 18”.
• Dutchwest Double-Wall Connector Information on assembling and installing double-wall connectors is provided by the manufacturer of the double-wall pipe. Follow the manufacturer’s installation instructions exactly.
Most manufacturers of prefabri- cated double-wall insulated chimneys also offer double- wall connector pipes. Using a chimney and connector pipe from the same manufacturer helps simplify the assembly and installation. • Securing the Connector to a Masonry Chimney The Dutchwest Convection heaters may be connected to either a freestanding masonry chimney or a masonry fireplace chimney. Freestanding Installations If the chimney connector must pass through a combus- tible wall to reach the chimney, follow the recommenda- tions in the wall pass-through section that follows.
• Dutchwest Fireplace Installations - Through the Fireplace The Convection heaters may be installed either without legs* as a fireplace insert, or with standard legs at- tached - depending on the safety regulations that apply to your situation, the height of the fireplace opening and your own preference. • Minimum Dimensions for Noncombustible Floor floor protection Protectors (Depth x Width): 6/27/00 djt Model U.S. Canada 2460 38” x 44” 42” x 48” (1067mm x 1219mm) 2461 38” x 48” 42” x 52” (1067mm x 1320mm) 2462 42” x 52”. • Dutchwest To install the heater without legs as a fireplace insert, the floor must be completely noncombustible, such as an unpainted concrete floor over earth. Many fireplaces do not satisfy the “completely non- combustible” requirement because the brick or con- crete hearth in front of the fireplace opening usually is supported by heavy wooden framing as in Figure 13.
• In addition, both Fireplace Adaptor and Fireplace Insert installations have special floor protection requirements that are addressed in the section on Floor Protection. 7001135 Model: 2460 2461 Side Walls (S) 20” (510mm) 24” (610mm) 23” (580mm) Trim (T) 12” (300mm) 12” (300mm) • Dutchwest Designing a Safe Installation The section that follows contains charts with the infor- mation that you’ll need to make your installation safe. Included are a chart to tell you exactly where to cut the hole in the ceiling so that the stove will meet clearance requirements, a chart that gives stove clearances for all installations, and a chart to illustrate the required sizes of wall shields for various installations. • Stove and Chimney Connector Clearance Charts Model 2460 Small Convection, and Model 2461 Large Convection: UNPROTECTED SURFACES Parallel Installations Stove Clearance Side No heat shields [A] 22” (560 mm) [B] 24” (610 mm) Rear exit, rear h.s. [G] 22” (560 mm) [H] 14” (360 mm) Top exit, rear h.s. • Measurements are from the centerline of the flue collar to the wall, not the wall protector.